Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

2017-12-11T16:46:25.504000Z

I'm sure that you have probably figured this out, but there are man pages for each of the scsirastools commands, installed with the rpm.
As a consolidated document, all of that information is also contained in the text UserGuide installed with the rpm, or available at http://scsirastools.sourceforge.net/docs/UserGuide

Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

2017-02-08T09:14:58.057000Z

Thanks for the reply.
My question was also how to start scirastools and what are the examples of syntacs?
There is a doubt about twin port connector. What are the controlers with this function and software based RAID that alows pass thry commands?
One half of same discs working without issue.
Thanks

Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

2017-02-05T19:46:15.491000Z

Dear all I am newbee with scsirastools and almost with linux too.
I have no idea how to start commands and is the Parted magic live USB compatabile with this utility.
I have sucsesefully formated to 512k sectoe size few of these ssd sas disk buth some of them are in status:

Sg utility

Fixed format, current; Sense key: Not Ready
Additional sense: Logical unit failure

And:

root@PartedMagic:~# sg_format -vvv /dev/sg5
open /dev/sg5 with flags=0x802
inquiry cdb: 12 00 00 00 24 00
NETAPP X452_1625500MCSG MQ00 peripheral_type: disk [0x0]
PROTECT=1
<< supports protection information>>
inquiry cdb: 12 01 00 00 24 00
inquiry: pass-through requested 36 bytes (data-in) but got 13 bytes
inquiry cdb: 12 01 80 01 00 00
inquiry: pass-through requested 256 bytes (data-in) but got 32 bytes
Unit serial number: S183NEAD300536
inquiry cdb: 12 01 83 01 00 00
inquiry: pass-through requested 256 bytes (data-in) but got 76 bytes
LU name: 50025384533094d0
mode sense (10) cdb: 5a 00 01 00 00 00 00 00 fc 00
duration=2 ms
mode sense (10):
Fixed format, current; Sense key: Not Ready
Additional sense: Logical unit failure
Field replaceable unit code: 1
Progress indication: 0.00%
Raw sense data (in hex):
70 00 02 00 00 00 00 10 00 00 00 00 3e 01 01 80
00 00 00 62 3e 01 00 00
pass-through requested 252 bytes (data-in) but got 0 bytes
MODE SENSE (10) command: Not ready sense

With --six is the same

Also with other command

Do you really want to reformat this device [y/n]? y

Prepare command ...
Done.
Send MODE SELECT command ...
Done.
Check status ...
Error: Check Condition
[valid=0] Info fld=0x0, Current sense key: Not Ready
Raw sense data (in hex):
70 00 02 00 00 00 00 10 00 00 00 00 3e 01 01 80
plus...: Driver_status=0x08 (DRIVER_SENSE,SUGGEST_OK)
Command NOT succesful!

Thanks,
regards

SAS Firware Update

2016-06-24T21:26:23.640000Z

I got the same error for every chunk size I attempted. I even tried on an 800GB Optimus Ascend model I have with EMC firmware and it gave the same response.

Are EMC drives just completely locked as far as non-emc firmware changes?

SAS Firware Update

2016-06-23T19:11:40.479000Z

Great, thanks. I will try these tonight and report back.

And yes, my original attempts were without -s and those didn't work either.

SAS Firware Update

2016-06-14T06:05:27.834000Z

Hello,

I am having problems doing a firmware update on a Sandisk Optimus Eco SSD (SDLLOC6R-016T-5CA1) that has EMC firmware loaded on it. I'd like to load the normal firmware from Sandisk.

Here is my log:

sudo sgdskfl -x -s 1024 -d /dev/sg7 -f k0A0.dob

sdelay = 10 sec
run-level = 1

            sgdskfl utility v1.66 for SCSI disks
          ******************************************

Log file /var/log/sgdskfl.log is open, debug=1

Num Name [bus:ch:id:lun] Type Vendor Device_Model FW Serial#_ Servo_
k=32768, /dev/sg7 open, sg_fd = 4
0 /dev/sg7 [8:0:0:0] Disk SNDKEMC CLAR1600 EE03 XXXXXXXX
Download ...
Selected 0: [0:0] SNDKEMC CLAR1600EE03XXXXXXXX
Reading image file k0A0.dob, size = 990720
Cannot open k0A0.tms, errno = 2
No servo image
Device [0] is ready for download
Starting download process for 1 disk.
Downloading Firmware image to disk 0 Tue Jun 14 00:44:45 2016
write_buffers(len=990720,mode=5)
split buffers: max_chunk=1024,save_mode=5
write_buffer: HDR=36, clen=10, buflen=1024, total=1070, bufid=0
writebuffer: timeout was = 6000, set to 12000, sts = 0
writebuffer cdb: 3b 04 00 00 00 00 00 04 00 00
write_buffer: Check Condition Driver_status=0x08 (DRIVER_SENSE,SUGGEST_OK)
sense error, key=05 asc=26 ascq=02 Illegal Request, PARAMETER VALUE INVALID
Error in Parameter List: Byte #? is in error.
Info valid=0, Current
write_buffer: Check Condition Driver_status=0x08 (DRIVER_SENSE,SUGGEST_OK)
sense error, key=05 asc=26 ascq=02 Illegal Request, PARAMETER VALUE INVALID
Error in Parameter List: Byte #? is in error.
Info valid=0, Current
len = 80, bufp = 0x112fff0, Buffer:
0000: 24 00 00 00 24 00 00 00 64 00 00 00 00 00 00 00
0010: 02 00 02 00 70 00 05 00 00 00 00 18 00 00 00 00
0020: 26 02 01 80 3b 04 00 00 00 00 00 04 00 00 44 4f
0030: 42 20 43 46 52 4d 00 1e 0f 00 00 01 00 00 00 1d
0040: 0f 00 00 1d 0f 00 22 00 00 00 00 00 00 00 00 00
len = 80, bufp = 0x112fff0, Buffer:
0000: 24 00 00 00 24 00 00 00 64 00 00 00 00 00 00 00
0010: 02 00 02 00 70 00 05 00 00 00 00 18 00 00 00 00
0020: 26 02 01 80 3b 04 00 00 00 00 00 04 00 00 44 4f
0030: 42 20 43 46 52 4d 00 1e 0f 00 00 01 00 00 00 1d
0040: 0f 00 00 1d 0f 00 22 00 00 00 00 00 00 00 00 00
writebuffer: set timeout back to 6000, sts = 0
[0] Error -2 in writing buffer
[0] closefd, sgfd=0

Can I please get some guidance on what I'm doing wrong and what I can try?

Thanks.

Recent posts to Discussion

Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

Starting scirastools - Formatting Samsung MZ6ER400HAGM-000G3 NETAPP Model : X452_1625500MCSG

SAS Firware Update

SAS Firware Update

SAS Firware Update