<?xml version="1.0" encoding="utf-8"?>
<feed xml:lang="en" xmlns="http://www.w3.org/2005/Atom"><title>Recent changes to patches</title><link href="https://sourceforge.net/p/tulip/patches/" rel="alternate"/><link href="https://sourceforge.net/p/tulip/patches/feed.atom" rel="self"/><id>https://sourceforge.net/p/tulip/patches/</id><updated>2004-03-19T15:53:53Z</updated><subtitle>Recent changes to patches</subtitle><entry><title>delay after stop rx/tx</title><link href="https://sourceforge.net/p/tulip/patches/20/" rel="alternate"/><published>2004-03-19T15:53:53Z</published><updated>2004-03-19T15:53:53Z</updated><author><name>Don Law</name><uri>https://sourceforge.net/u/donnieblaw/</uri></author><id>https://sourceforge.netb6d28a088c9426bfda79bbf219d45895bb496427</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;Delay after telling chip to stop and before changing&lt;br /&gt;
any ring values.  This fixes a rare but nasty problem&lt;br /&gt;
when the tulip chip performs a portion of a DMA in&lt;br /&gt;
progress to the wrong location in memory.  The symptom&lt;br /&gt;
is that apparently random areas of memory in the kernel&lt;br /&gt;
get corrupted with a portion of the payload of an&lt;br /&gt;
incoming packet when the chip is stopped (ifconfig ethx&lt;br /&gt;
down).  If debugging is enabled (DEBUG) in the kernel,&lt;br /&gt;
it often appears as a BUG panic in&lt;br /&gt;
kmem_cache_alloc_one_tail.  If debugging is off, it&lt;br /&gt;
often appears as a panic with a message like "Unable to&lt;br /&gt;
handle kernel paging request at virtual address 1eee6464"&lt;/p&gt;
&lt;p&gt;In my testing, the problem showed up about 1% of the&lt;br /&gt;
time during an ifconfig down with a 21143 chip on an&lt;br /&gt;
i386 system.&lt;/p&gt;
&lt;p&gt;According to the 21143 hardware reference manual rev.&lt;br /&gt;
1.0, in the description of bit 1 of the CSR6 register:&lt;br /&gt;
"When cleared, the receive process enters the stopped&lt;br /&gt;
state after completing the reception of the current&lt;br /&gt;
frame."  This patch adds a delay of 1500 microseconds&lt;br /&gt;
after clearing bit 1, which is ample time for a&lt;br /&gt;
1536-byte frame to be received on a 10BT connection and&lt;br /&gt;
then be DMA'ed over a 33Mhz PCI bus.&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>802.1Q (VLAN) fix for Linux 2.4.20</title><link href="https://sourceforge.net/p/tulip/patches/19/" rel="alternate"/><published>2003-02-23T09:30:22Z</published><updated>2003-02-23T09:30:22Z</updated><author><name>Anonymous</name><uri>https://sourceforge.net/u/userid-None/</uri></author><id>https://sourceforge.net68f97c2e793e77ada9cdd92e900789bcebcd612f</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;Apply this patch in the driver/net/tulip directory.&lt;br /&gt;
Solves MTU problems with Tulip driver when using &lt;br /&gt;
VLANs (802.1Q Trunking).&lt;/p&gt;
&lt;p&gt;patch done from hints given by &lt;br /&gt;
Ben.McKeegan@fitz.cam.ac.uk&lt;br /&gt;
on &lt;a href="http://www.candelatech.com/~greear/vlan.html#setup" rel="nofollow"&gt;http://www.candelatech.com/~greear/vlan.html#setup&lt;/a&gt;&lt;/p&gt;
&lt;p&gt;to contact me:&lt;br /&gt;
vigneron@remcomp.fr&lt;br /&gt;
&lt;a href="http://www.remcomp.fr/" rel="nofollow"&gt;http://www.remcomp.fr/&lt;/a&gt;&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>Patch for SMC1255FTX card</title><link href="https://sourceforge.net/p/tulip/patches/18/" rel="alternate"/><published>2003-01-15T13:48:30Z</published><updated>2003-01-15T13:48:30Z</updated><author><name>Gernot Hillier</name><uri>https://sourceforge.net/u/userid-633130/</uri></author><id>https://sourceforge.net7214be16fad5d3a4f9e76ddba44b45627baa0b6b</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;I ported some ancient driver of SMC to a current patch for the Tulip &lt;br /&gt;
driver. It supports the SMC1255FTX card which has a fiber and a tp &lt;br /&gt;
connector. &lt;/p&gt;
&lt;p&gt;On open(), it will enable the fiber port on the card, have a look if it &lt;br /&gt;
gets a link and then switch back to tp and leave this as default. &lt;/p&gt;
&lt;p&gt;All changes should only have an effect for tulip cards - aside some &lt;br /&gt;
small fix in tulip.h (tulip_private/default_port was defined to small). &lt;/p&gt;
&lt;p&gt;I tested it successfully for several weeks now on my desktop and &lt;br /&gt;
think it's ready for other eyes now ;-)) &lt;/p&gt;
&lt;p&gt;Please have a look at it and apply if you think it's ok. &lt;/p&gt;
&lt;p&gt;TIA! &lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>ADM9511</title><link href="https://sourceforge.net/p/tulip/patches/17/" rel="alternate"/><published>2002-05-16T10:02:29Z</published><updated>2002-05-16T10:02:29Z</updated><author><name>Anonymous</name><uri>https://sourceforge.net/u/userid-None/</uri></author><id>https://sourceforge.net693c69c3304299eac64a36a7a714a66aec69f482</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;On my environment, ADM9511 can't work.&lt;br /&gt;
Perhaps the pci_device_id entry for ADM9511(?) is &lt;br /&gt;
wrong.&lt;br /&gt;
I could fix the problem with following patch.&lt;/p&gt;
&lt;h1 id="_1"&gt;=======================================================&lt;/h1&gt;
&lt;p&gt;RCS file: /cvsroot/tulip/tulip/src/tulip_core.c,v&lt;br /&gt;
retrieving revision 1.28&lt;br /&gt;
diff -r1.28 tulip_core.c&lt;br /&gt;
212c212,213&lt;br /&gt;
&amp;amp;lt;       { 0x1113, 0x9511, PCI_ANY_ID, PCI_ANY_ID, 0, &lt;br /&gt;
0, COMET },&lt;br /&gt;
---&lt;br /&gt;
&amp;amp;gt;       { 0x1113, 0x9511, PCI_ANY_ID, PCI_ANY_ID, 0, &lt;br /&gt;
0, COMET }, /* perhaps 0x1113 is miss spelling */&lt;br /&gt;
&amp;amp;gt;       { 0x1317, 0x9511, PCI_ANY_ID, PCI_ANY_ID, 0, &lt;br /&gt;
0, COMET },&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>setup fix for LNE100TX with LC82C168</title><link href="https://sourceforge.net/p/tulip/patches/16/" rel="alternate"/><published>2002-04-16T18:16:41Z</published><updated>2002-04-16T18:16:41Z</updated><author><name>Mark Vytlacil</name><uri>https://sourceforge.net/u/mvyt/</uri></author><id>https://sourceforge.netf72a64b8ea4cfb350fb9239dfc8763f7628b3687</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;Old LNE100TX would not see packets addressed to its MAC unless the setup frame was resent. It appears that &lt;br /&gt;
the card will not act appropriately on a setup frame while it is in the process of  autonegotiation. The patch &lt;br /&gt;
delays transmitting the setup frame until do_pnic_nway() restarts RxTx.&lt;/p&gt;
&lt;p&gt;Driver did not keep card in allmulti or promiscuous mode when explicitly set. Fix in do_pnic_nway().&lt;/p&gt;
&lt;p&gt;Typo error in tulip_init_one() set CSR6 instead of 0xB8. Not much effect.&lt;/p&gt;
&lt;p&gt;This patch against 1.1.8 makes my card work, but it may not be the best way.&lt;/p&gt;
&lt;p&gt;Mark&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>21142 media select fix</title><link href="https://sourceforge.net/p/tulip/patches/15/" rel="alternate"/><published>2002-03-22T23:06:28Z</published><updated>2002-03-22T23:06:28Z</updated><author><name>Arnout Engelen</name><uri>https://sourceforge.net/u/raboofje/</uri></author><id>https://sourceforge.net67c03eb632d937f19215a5657536864804a77188</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;I noticed that after the following change:&lt;/p&gt;
&lt;p&gt;* 21142.c (t21142_lnk_change): Pass arg startup==1&lt;br /&gt;
to tulip_select_media, in order to force csr13 to be&lt;br /&gt;
zeroed out prior to going to full duplex mode.  Fixes&lt;br /&gt;
autonegotiation on a quad-port Znyx card.&lt;br /&gt;
(from Stephen Dengler)&lt;/p&gt;
&lt;p&gt;my ACCTON EN2220 pcmcia card stopped working (lspci: Digital Equipment Corporation DECchip 21142/43 (rev 30)).&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>21041 fix patch for 2.4.x kernels</title><link href="https://sourceforge.net/p/tulip/patches/14/" rel="alternate"/><published>2001-12-18T04:47:44Z</published><updated>2001-12-18T04:47:44Z</updated><author><name>Jeff Garzik</name><uri>https://sourceforge.net/u/jgarzik/</uri></author><id>https://sourceforge.netf2a474ee854da6d43434635a8a742f73ccd3f70a</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;This an attempt to fix 21041 media selection for recent&lt;br /&gt;
tulip drivers.&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>Patch for tulip_old</title><link href="https://sourceforge.net/p/tulip/patches/13/" rel="alternate"/><published>2001-12-03T19:07:54Z</published><updated>2001-12-03T19:07:54Z</updated><author><name>Felipe Massia Pereira</name><uri>https://sourceforge.net/u/felmasper/</uri></author><id>https://sourceforge.netc173b3fa7304e26591feba1d84c2b7c60d07faa0</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;My ethernet card was working in RH7.1 but stopped with&lt;br /&gt;
RH7.2 (with the new tulip module). I made a diff&lt;br /&gt;
between the drivers and found out a different line. Now&lt;br /&gt;
it works.&lt;/p&gt;
&lt;p&gt;Here's dmesg...&lt;/p&gt;
&lt;p&gt;Linux Tulip driver version 0.9.14 (February 20, 2001)&lt;br /&gt;
PCI: Found IRQ 11 for device 00:12.0&lt;br /&gt;
eth0: Digital DS21143 Tulip rev 48 at 0xec00,&lt;br /&gt;
00:00:F8:1A:22:6F, IRQ 11.&lt;br /&gt;
eth0:  EEPROM default media type Autosense.&lt;br /&gt;
eth0:  Index #0 - Media 10baseT (#0) described by a&lt;br /&gt;
21142 Serial PHY (2) block.&lt;br /&gt;
eth0:  Index #1 - Media 10baseT-FD (#4) described by a&lt;br /&gt;
21142 Serial PHY (2) block.&lt;br /&gt;
eth0:  Index #2 - Media 100baseTx (#3) described by a&lt;br /&gt;
21143 SYM PHY (4) block.&lt;br /&gt;
eth0:  Index #3 - Media 100baseTx-FD (#5) described by&lt;br /&gt;
a 21143 SYM PHY (4) block.&lt;/p&gt;
&lt;p&gt;And here's /proc/pci...&lt;br /&gt;
Bus  0, device  18, function  0:&lt;br /&gt;
Ethernet controller: Digital Equipment Corporation&lt;br /&gt;
DECchip 21142/43 (rev 48).&lt;br /&gt;
IRQ 11.&lt;br /&gt;
Master Capable.  Latency=165.  Min Gnt=20.Max Lat=40.&lt;br /&gt;
I/O at 0xec00 [0xec7f].&lt;br /&gt;
Non-prefetchable 32 bit memory at 0xfedffc00&lt;br /&gt;
[0xfedffc7f].&lt;/p&gt;
&lt;p&gt;--&lt;br /&gt;
Hope it helps,&lt;br /&gt;
Felipe--&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>MTU fix against DEVEL &amp;amp;amp; STABLE</title><link href="https://sourceforge.net/p/tulip/patches/12/" rel="alternate"/><published>2001-11-11T13:38:37Z</published><updated>2001-11-11T13:38:37Z</updated><author><name>Paul P Komkoff Jr</name><uri>https://sourceforge.net/u/stingr/</uri></author><id>https://sourceforge.netbc864c83635cfdf627b6d4fe0e9723f4371a2fe0</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;MTU patch against both devel and stable branches. &lt;br /&gt;
Needed to run vlans on tulip.&lt;/p&gt;&lt;/div&gt;</summary></entry><entry><title>[Bug #124918] packet received prior to buffer allocation cr</title><link href="https://sourceforge.net/p/tulip/patches/11/" rel="alternate"/><published>2001-01-17T16:32:06Z</published><updated>2001-01-17T16:32:06Z</updated><author><name>Paul Bame</name><uri>https://sourceforge.net/u/paulbame/</uri></author><id>https://sourceforge.nete0a6d54cc8b308f157f4ca5bda8f33c5a851684e</id><summary type="html">&lt;div class="markdown_content"&gt;&lt;p&gt;See Bug #124918&lt;/p&gt;&lt;/div&gt;</summary></entry></feed>